Home

Traffic Light Control

Statement: Design a microprocessor system to control traffic lights. The traffic light arrangement is as shown in Fig. The traffic should be controlled in the following manner.

1) Allow traffic from W to E and E to W transition for 20 seconds. 2) Give transition period of 5 seconds (Yellow bulbs ON) 3) Allow traffic from N to 5 and 5 to N for 20 seconds 4) Give transition period of 5 seconds (Yellow bulbs ON) 5) Repeat the process.

HARDWARE FOR TRAFFIC LIGHT CONTROL

Fig. shows the interfacing diagram to control 12 electric bulbs. Port A is used to control lights on N-S road and Port B is used to control lights on W-E road. Actual pin connections are listed in Table 1 below.

The electric bulbs are controlled by relays. The 8255 pins are used to control relay on-off action with the help of relay driver circuits. The driver circuit includes 12 transistors to drive 12 relays. Fig. also shows the interfacing of 8255 to the system.

INTERFACING DIAGRAM

SOFTWARE FOR TRAFFIC LIGHT CONTROL

Source Program 1:

MVI A, 80H : Initialize 8255, port A and port B
OUT 83H (CR) : in output mode
START: MVI A, 09H
OUT 80H (PA) : Send data on PA to glow R1 and R2
MVI A, 24H
OUT 81H (PB) : Send data on PB to glow G3 and G4
MVI C, 28H : Load multiplier count (40ıο) for delay
CALL DELAY : Call delay subroutine
MVI A, 12H
OUT (81H) PA : Send data on Port A to glow Y1 and Y2
OUT (81H) PB : Send data on port B to glow Y3 and Y4
MVI C, 0AH : Load multiplier count (10ıο) for delay
CALL: DELAY : Call delay subroutine
MVI A, 24H
OUT (80H) PA : Send data on port A to glow G1 and G2
MVI A, 09H
OUT (81H) PB : Send data on port B to glow R3 and R4
MVI C, 28H : Load multiplier count (40ıο) for delay
CALL DELAY : Call delay subroutine
MVI A, 12H
OUT PA : Send data on port A to glow Y1 and Y2
OUT PB : Send data on port B to glow Y3 and Y4
MVI C, 0AH : Load multiplier count (10ıο) for delay
CALL DELAY : Call delay subroutine
JMP START

Delay Subroutine:

DELAY: LXI D, Count : Load count to give 0.5 sec delay
BACK: DCX D : Decrement counter
MOV A, D
ORA E : Check whether count is 0
JNZ BACK : If not zero, repeat
DCR C : Check if multiplier zero, otherwise repeat
JNZ DELAY
RET : Return to main program

Related Programs (Click down)

Generate and display binary up counter

Generate and display BCD up counter with frequency 1Hz

Generate and display BCD down counter

Generate and display the contents of decimal counter

Light controlled thyristor circuitGK light control thyristor, also known as optical switch, a photosensitive device. 1. The structure...A microcontroller-based control system for variable frequency refrigerator circuitThe AT89C51 microcontroller as the core, the work of the refrigerator to control the process, so tha...Light controlled LED lighting circuitThis is a light control function with LED lights, it does not work during the day, lights automatica...Infrared Sensor controlled Lamp Control Chip PT8A2621 and its applicationAbstract: The light control with infrared sensing chip PT8A2621 the main features of pin functions, ...Road construction warning lights control circuit urban road construction at night is usually set at the construction site and opened the red...Automatic traffic light controller circuitthe circuit components are used: 78M05 CCD4011 Figure shows the automatic control circuit of traf...LC172 based sound and light dual-controlled four-phase pulse distribution control circuit for LanternLC172 sound and light dual-controlled four-phase control circuit pulse distribution Lantern The ci...Automatic energy-saving light with LED light control circuitPast light control circuits are used incandescent load, although used at night, to stop working duri...555 based automatic flashing light control for traffic signalFigure shows signs of light controlled automatic flashing lights circuit. The circuit consists of st...LC181 based three-way audio control and voltage-controlled lightsLCl81 audio control circuit voltage-controlled three-way lights the circuit components are used: L...PIC16C72 microcontroller based control system for air-conditioning circuit Wall split air conditioning heat pump with its superior performance, are increasingly being ...Automatic brightness control circuit with turn ON LCD backlight using visible light sensor LX1970When the ambient light was dimmed, LX1970 can automatically open the LCD's backlight, so the white L...LPC2104-based design of intelligent lighting controller circuitLPC2104 has a rich peripheral interface resources, and have a high reliability and speed, very suita...YH2902A based multi-functional lighting control circuit with delay timing controlBy the timing control modules YH2902A versatile multi-functional lighting control circuit YH2902A de...Vehicle flashing lights controller circuitThis example describes the motor vehicle flashing lights controller , with lantern cycle, braking an...5GMl68 based audio control circuit for voltage-controlled holiday lightsShown for the introduction of 5GM168 control circuit consisting of four lights (G-foot vacant chip),...Dual control doppler effect and light socket controlled automatic door circuit using RD627Circuit as shown. It consists of the Doppler effect sensor head, light control switch, one-shot, SCR...A neon light control circuitThe cases described in neon light control , does not work during the day , night work automatically ...Lighting Control Circuits-8// Lamp circuit with delay relay 1 ...LED lighting control circuitThis is a light control function with LED lights, it does not work during the day, lights automatica...

Free Electronic projects & 8085 projects

Recent Projects

Traffic Light Control